scrobble.life
Hive Motors

Troubleshooting and Repairing a Seized Evaporator Blower Motor [ENG/SPA]

We’d been without AC at home for three days—it had to break down right during the hottest spell of the year, courtesy of the Super El Niño phenomenon stealing away all our natural end-of-year relief. When I turned the unit on, the compressor would kick in, but the evaporator blower wheel wouldn't spin. My first thought was that it was seized up, but when I gave it a spin by hand, it turned without any problem.

Diagnóstico y reparación de un motor de evaporador con rodamientos trancados

Llevábamos tres días sin aire acondicionado en casa, se dañó precisamente en estos días donde ha hecho más calor; el fenómeno del super niño ha hecho que nuestro fin de año pierda su frescura natural. Resulta que al encender el equipo, el compresor comenzaba a trabajar, pero la turbina del evaporador no giraban. Lo primero que pensé fue que se había trancado, pero cuando lo giro con mi mano, lo hacia sin problema.

1000543617.jpg

I started digging in carefully, but didn't spot the issue on my first pass. I initially suspected a blown run capacitor. But after checking it with the multimeter, it was putting out the right voltage, which is what led me to pull the motor out entirely—and that's when I found the culprit. Because the internal bearings had started binding up, the current draw spiked, and one of the power wires melted right through, super close to the motor housing.

Comienzo a revisar con detenimiento y en el primer intento no consigo la falla. Lo primero que pensé fue que el condensador de arranque se había dañado. Pero tras medir con el multímetro entregaba bien el voltaje, por eso decidí desmontarlo y fue así que encontré la falla. Producto de que sus rodamientos internos comenzaron a trancarse, la corriente se elevo y uno de los cables que lo alimenta eléctricamente se fundió, pero exactamente en un punto muy cercano a la carcasa del motor.

1000541192.jpg

Pulling the motor armature is pretty straightforward; you just pop off one of the end caps. That let me inspect the bearings, and sure enough, they were binding up and slightly rusted. I cleaned them up with alcohol and they felt a bit better, but you could hear the internal balls grinding away. I just went ahead and bought new ones so I could focus on fixing that wire, which was the real headache.

Sacar el inducido del motor es sencillo, basta con retirar una de las tapas de cualquiera de los dos lados. Así pude evaluar los rodamientos y efectivamente estaban algo trancados y ligeramente con óxido. Los limpie con alcohol y mejoraron pero ya se sentían que sus esferas internas sonaban. Los compré para reemplazarlos y poder concentrarme en reparar el cable que si estaba más complicado.

1000543618.jpg 1000542080.jpg 1000542081.jpg

Since it's a sealed motor, you can't get to the windings and internal wiring without breaking into it. So, I slowly and carefully chipped away around the tiny bit of exposed wire left until I had enough slack to work with. I tinned it with solder and then insulated it with silicone. After that, I reinstalled the new bearings with a lot of care, making sure to match the exact placement of the old ones.

Al ser un motor encapsulado, no es posible acceder al devanado y a su vez los cables sin romperlo. Así que poco a poco fui rompiendo con cuidado alrededor del pedazo de cable que quedó descubierto, hasta tener un trozo suficiente para poder soldarlo. Le aplique estaño y luego lo aisle con silicona. Luego instale los nuevos rodamientos con sumo cuidado, respetando la posición de los anteriores.

1000541236.jpg 1000542082.jpg

I hooked the fully assembled motor back up to the capacitor and tested it—and it ran like a dream. That’s how I managed to save the motor, dodge a lengthy parts search for an older unit, and avoid shelling out a ton of cash on a custom workaround. Total damage? Just $4 for a pair of new bearings.

Probe conectando el motor ya armado al condensador de arranque y funcionó de maravilla. Así fue como pude salvar el motor y ahorrarme una busque que quizás me tomaría mucho tiempo, por ser en equipo de varios años, o tener que hacer una adaptación gastando una cantidad considerable de dinero, y solo me costaron $4 los dos rodamientos.


Photos taken by ©danielcarrerag copyright reserved. These images may not be reproduced, distributed or used without the express permission of the author.

Comments

No comments yet — be the first.